thailand elevator, thailand lift,thai lift, thai elevator, asia elevator, asia lift, thailand escalator, asia escalator, lift spare parts, lift maintenance, lift modernization
  The whole world of elevator, escalator and spare Parts | ASIA SCHNEIDER (THAILAND) CO.,LTD.
 
 
 
FES Type Escalator
Others Escalator
 
 
 
 
Standard safety features

Drive-Chain Contact
This contact monitors the Drive-Chain for breakage. When actuated, the contact will stop the escalator.

Skirting Contacts
These contacts have been installed at both the top and bottom of the escalator at the transition curve. If an object gets caught between the step and the skirting panel, the resultant pressure on the skirting panel will actuate one of these contacts, thereby disabling and switching off the escalator.

Handrail Entry Contacts
The handrail entry contacts are located far beneath the head of the balustrade. The handrail entry contacts are so positioned that if there is any danger of an object becoming wedged in the handrail entry points, a contact will actuate and switch off the escalator.

Step chains contacts
Located in the lower step-reversing compartment, these contacts monitor the step chains for elongation, breakage or shortening of one or both of the step chains. When actuated, the monitoring contacts will disable and stop the escalator's further movement.

Step Sag contacts
Fixed at the start sections of both inclined upper and lower transition curves, it will be actuated to stop escalator in case step (including step roller) sags more than 3mm.

Phase Monitor
This is a safety feature, which monitors the main power supply and disables the escalator in the event of phase failure or phase reversal.

Motor Overload & Overheat (Relay)
This relay monitors the motor working condition. In case of motor over loaded or overheated, the escalator should be stopped.

Comb Contacts
If a foreign object is caught between the comb, and the steps, the resulting pressing action will move comb plates backwards and actuate a safety contacts, thereby switching off the escalator.

Step Gap Illumination
Special green lamps in the form of fluorescent tubes,mounted on both the top and bottom of the escalator, make the individual steps clearly discernible and distinguishable,especially at the horizontal runs. Boarding the escalator is therefore made much easier for the young, elderly and inexperienced persons.

Maintenance locking device
The normal key start function will be invalid while Maintenance locking device is used. The inspection socket in up and down machine room couldn't use at the same time.

Alarm buzzer
The buzzer is located in up/down machine room, which can call passenger's attention during starting the escalator.

Speed Monitor with Anti-reverse Function
Fixed at the bottom of brake, it is to monitor the speed of flywheel as well as to avoid reverse and will stop escalator in case rated speed is over 120% or under 80%.

Step anti-static brush
Its location is in the truss, under the step and near linear end. It can eliminate step static effectively.

Controller lift device
It is located in machine room, which is convenient to lift the controller for inspection and testing the escalator.

Emergency stop buttons
Emergency stop buttons have been built into operation panel at the upper and lower ends of the escalator. As the name of the button so implies, the emergency stop buttons may be used to switch off the escalator manually, during emergencies or even during normal condition.

Step reversing fences
The fence is fixed at the end of step reversing point in the machine room and promotes its safe protection.

Handrail anti-static roller
The roller is located under the both end of the handrail in the truss.

Service brake release contact
This contact is fixed at both brake arm to monitor whether the brake is open or not. If the brake operates abnormal, the equipment couldn't start and buzzer will alarm. Drive-Chain Contact
This contact monitors the Drive-Chain for breakage. When actuated, the contact will stop the escalator.

Skirting Contacts
These contacts have been installed at both the top and bottom of the escalator at the transition curve. If an object gets caught between the step and the skirting panel, the resultant pressure on the skirting panel will actuate one of these contacts, thereby disabling and switching off the escalator.

Handrail Entry Contacts
The handrail entry contacts are located far beneath the head of the balustrade. The handrail entry contacts are so positioned that if there is any danger of an object becoming wedged in the handrail entry points, a contact will actuate and switch off the escalator.

Step chains contacts
Located in the lower step-reversing compartment, these contacts monitor the step chains for elongation, breakage or shortening of one or both of the step chains. When actuated, the monitoring contacts will disable and stop the escalator's further movement.

Step Sag contacts
Fixed at the start sections of both inclined upper and lower transition curves, it will be actuated to stop escalator in case step (including step roller) sags more than 3mm.

Phase Monitor
This is a safety feature, which monitors the main power supply and disables the escalator in the event of phase failure or phase reversal.

Motor Overload & Overheat (Relay)
This relay monitors the motor working condition. In case of motor over loaded or overheated, the escalator should be stopped.

Comb Contacts
If a foreign object is caught between the comb, and the steps, the resulting pressing action will move comb plates backwards and actuate a safety contacts, thereby switching off the escalator.

Step Gap Illumination
Special green lamps in the form of fluorescent tubes,mounted on both the top and bottom of the escalator, make the individual steps clearly discernible and distinguishable,especially at the horizontal runs. Boarding the escalator is therefore made much easier for the young, elderly and inexperienced persons.

Maintenance locking device
The normal key start function will be invalid while Maintenance locking device is used. The inspection socket in up and down machine room couldn't use at the same time.

Alarm buzzer
The buzzer is located in up/down machine room, which can call passenger's attention during starting the escalator.

Speed Monitor with Anti-reverse Function
Fixed at the bottom of brake, it is to monitor the speed of flywheel as well as to avoid reverse and will stop escalator in case rated speed is over 120% or under 80%.

Step anti-static brush
Its location is in the truss, under the step and near linear end. It can eliminate step static effectively.

Controller lift device
It is located in machine room, which is convenient to lift the controller for inspection and testing the escalator.

Emergency stop buttons
Emergency stop buttons have been built into operation panel at the upper and lower ends of the escalator. As the name of the button so implies, the emergency stop buttons may be used to switch off the escalator manually, during emergencies or even during normal condition.

Step reversing fences
The fence is fixed at the end of step reversing point in the machine room and promotes its safe protection.

Handrail anti-static roller
The roller is located under the both end of the handrail in the truss.

Service brake release contact
This contact is fixed at both brake arm to monitor whether the brake is open or not. If the brake operates abnormal, the equipment couldn't start and buzzer will alarm. Drive-Chain Contact
This contact monitors the Drive-Chain for breakage. When actuated, the contact will stop the escalator.

Skirting Contacts
These contacts have been installed at both the top and bottom of the escalator at the transition curve. If an object gets caught between the step and the skirting panel, the resultant pressure on the skirting panel will actuate one of these contacts, thereby disabling and switching off the escalator.

Handrail Entry Contacts
The handrail entry contacts are located far beneath the head of the balustrade. The handrail entry contacts are so positioned that if there is any danger of an object becoming wedged in the handrail entry points, a contact will actuate and switch off the escalator.

Step chains contacts
Located in the lower step-reversing compartment, these contacts monitor the step chains for elongation, breakage or shortening of one or both of the step chains. When actuated, the monitoring contacts will disable and stop the escalator's further movement.

Step Sag contacts
Fixed at the start sections of both inclined upper and lower transition curves, it will be actuated to stop escalator in case step (including step roller) sags more than 3mm.

Phase Monitor
This is a safety feature, which monitors the main power supply and disables the escalator in the event of phase failure or phase reversal.

Motor Overload & Overheat (Relay)
This relay monitors the motor working condition. In case of motor over loaded or overheated, the escalator should be stopped.

Comb Contacts
If a foreign object is caught between the comb, and the steps, the resulting pressing action will move comb plates backwards and actuate a safety contacts, thereby switching off the escalator.

Step Gap Illumination
Special green lamps in the form of fluorescent tubes,mounted on both the top and bottom of the escalator, make the individual steps clearly discernible and distinguishable,especially at the horizontal runs. Boarding the escalator is therefore made much easier for the young, elderly and inexperienced persons.

Maintenance locking device
The normal key start function will be invalid while Maintenance locking device is used. The inspection socket in up and down machine room couldn't use at the same time.

Alarm buzzer
The buzzer is located in up/down machine room, which can call passenger's attention during starting the escalator.

Speed Monitor with Anti-reverse Function
Fixed at the bottom of brake, it is to monitor the speed of flywheel as well as to avoid reverse and will stop escalator in case rated speed is over 120% or under 80%.

Step anti-static brush
Its location is in the truss, under the step and near linear end. It can eliminate step static effectively.

Controller lift device
It is located in machine room, which is convenient to lift the controller for inspection and testing the escalator.

Emergency stop buttons
Emergency stop buttons have been built into operation panel at the upper and lower ends of the escalator. As the name of the button so implies, the emergency stop buttons may be used to switch off the escalator manually, during emergencies or even during normal condition.

Step reversing fences
The fence is fixed at the end of step reversing point in the machine room and promotes its safe protection.

Handrail anti-static roller
The roller is located under the both end of the handrail in the truss.

Service brake release contact
This contact is fixed at both brake arm to monitor whether the brake is open or not. If the brake operates abnormal, the equipment couldn't start and buzzer will alarm.
       

viagra suisse levitra suisse cialis suisse cialis svizzera viagra svizzera kamagra gel kamagra 100 cialis generico precio viagra kamagra gel levitra generico cialis sin receta viagra generico viagra pfizer comprar lovegra viagra o cialis viagra precio cialis precio kamagra gel

cialis norge viagra pris cialis generico cialis billigt kamagra pris viagra sverige cialis sverige viagra billigt kamagra gel cialis pris levitra generika cialis schweiz viagra bestellen viagra schweiz kamagra schweiz cialis bestellen priligy kaufen kamagra schweiz

 
à¡ƠèÂǡѺàẲ | ÊÔ¹¤é̉ áÅĐºĂÔ¡̉?/a> | ¢è̉ÇỂ?/a> | ¶̉?- µÍ?/a> | µÔ´µèÍàĂ?/a> | ÊÁÑ¤Ă§̉¹
thailand elevator, thailand lift,thai lift, thai elevator, asia elevator, asia lift, thailand escalator, asia escalator, lift spare parts, lift maintenance, lift modernization
Copyright © 2007 Asia Schneider Co,.Ltd. All rights reserved.